It is preview of ford fuse box diagram...
On our site you will be able to find necessary you information about
Ford fuse box diagram
HOW TO START THE ENGINEIt would seem, than that is easier - has turned a key in the lock of ignition - and it is ready! But so, unfortunately, happens not always: vehicles too break. If the driver has not enough experience or the car is bought recently? We Shall try you to help. Perhaps, our helps will be useful in road?
So, we shall examine some possible variants.
I. At turn of a key of ignition in position "starter" the engine is not turned also click of operation of the involving relay of a starter is not audible.
1. To check up
safety fuses.
2. To check up blocking a starter.
3. To check up a condition of the accumulator.
4. To check up fastening wires to the accumulator.
5. To check up involving relay of a starter.
6. To check up contact group of the lock of ignition.
II. At turn of a key of ignition in position "starter" the engine is not turned. Click of operation of the involving relay of a starter is audible.
1. To check up a condition of the accumulator.
2. To check up fastening wires to the accumulator.
3. To check up effort cranking the engine.
4. To check up a starter.
5. To check up involving relay.
6. To check up fastening a "minus" wire to the engine.
III. At inclusion of a starter the engine is turned with the speed insufficient for start-up.
1. To check up a condition of oil in crankcase the engine.
2. To check up a condition of the accumulator.
3. To check up fastening wires to the accumulator.
4. To check up fastening a "minus" wire to the engine.
5. To check up effort cranking the engine.
6. To check up a starter.
7. To check up fastening wires to the involving
relay.
IV. The Petrol engine is turned well, but not started.
1. To check up safety fuses and all sockets.
2. To check up a spark on candles.
3. To check up receipt of fuel in an inlet collector.
4. To check up the gauge of start-up and starting injector.
5. To check up integrity of a gear belt gas distribution.
6. To check up position valve in the carburettor.
7. To check up labels gas distribution.
8. To check up a compression in cylinders.
9. To check up ignition device.
10. To check up a computer.
11. To check up the switchboard and the high-voltage coil.
12. To check up an exhaust path.
V. The diesel engine is not started.
1. To check up safety fuses and all electric sockets.
2. To check up work shutoff the valve of the fuel pump.
3. To check up a voltage on candles incandescence.
4. To check up presence of fuel in "test" and absence of air in fuel.
5. To check up candles incandescence and a voltage on them.
6. To check up a compression.
7. To check up labels of a drive of the fuel pump of a high pressure.
8. To check up atomizers.
9. To clean (to repair) fuel pump of a high pressure.
Check of blocking of a starter
 |
The information is given by
http://fordfusebox.freehostia.com
______________________________________________________________________
Replacement of safety fusesThe majority of safety fuses and some relays are installed in interior of the car at the left under a sterring wheel. The block of safety fuses and the relay is located from the left back party{side} of a motor compartment for damping rack. Before replacement of a safety lock{fuse} or the relay switch off ignition and all consumers of the electric power (for example, a radio receiver).
SEQUENCE OF WORKS
1. A tweezers (is in a cover of the block of safety fuses) or flat-nose pliers cautiously get fused safety fuse from the holder.
2. Insert in the holder the new safety fuse calculated on the same force of a current. Keep up correct installation of a safety fuse.
3. If the new safety fuse at once will fuse, you check up, maybe, have installed the fuse calculated on smaller force of a current of protection. If the installed safety fuse will fuse again, check up the electric circuit protected by a safety fuse
guide to ford fuse box diagram___________________________________________________________
|
